OSEEC.032 explains why a variable-frequency drive (VFD) can gradually damage an electric motor’s bearings even when speed control works normally. The previous OSEEC.031 covered motor-terminal voltage spikes. Bearing currents involve another effect: high-frequency electrical paths through or around the rotating shaft.
Key Learning Objectives
- Define PWM, common-mode voltage, shaft voltage, electrical discharge machining (EDM), and fluting.
- Explain how a bearing’s lubricant film can become part of an electrical discharge path.
- Distinguish electrical bearing damage from mechanical or lubrication problems.
- Describe protective methods, diagnostic evidence, and safe work boundaries.
Prerequisites: OSEEC.018 on VFD operation and basic motor construction.
Definitions: from switching to bearing discharge
Pulse-width modulation (PWM) controls the effective voltage and frequency delivered to a motor using rapid inverter switching. Common-mode voltage is the average of the three instantaneous output phase voltages relative to a chosen reference; it is not necessarily zero during switching. Rapid voltage changes couple through unintended capacitances between windings, rotor, frame, and nearby metal.
Shaft voltage is a potential difference between the rotating shaft and a reference such as the motor frame. The insulating oil or grease film inside a bearing can initially impede conduction. When an electrical path breaks down, a short current pulse may cross the rolling contact. Repeated microscopic arcs cause electrical discharge machining (EDM), where sparks erode metal. Many discharge pits can create a frosted surface; periodic washboard-like grooves are called fluting. ABB describes these mechanisms in its motor-bearing engineering guidance.
Why a bearing can carry current
A motor includes unavoidable parasitic capacitance between conductive parts separated by insulation. During fast PWM transitions, a portion of high-frequency current can pass through these capacitances. Depending on motor size, grounding, coupling to the driven machine, and installation, shaft-to-bearing discharge or circulating bearing current can result. The bearing is not intentionally wired into the power circuit; it can become an unintended return route.
Illustrative calculation: for a simplified isolated capacitor, V = Q/C. An accumulated charge of 2 nanocoulombs on 200 picofarads would produce 10 volts. Actual motor shaft voltage cannot be predicted from a lone capacitance: it depends on the full high-frequency network, switching waveform, and discharge conditions. No universal safe shaft-voltage threshold follows from the example.
Electrical versus ordinary bearing wear
Increasing vibration, temperature, or noise does not uniquely prove EDM. Contaminated lubricant, misalignment, excess load, and ordinary fatigue may produce similar symptoms. Electrical pitting or fluting found during a qualified teardown strengthens the hypothesis, especially when supported by correctly obtained shaft-voltage waveforms and installation records. Review OSETC.043 on bearing condition checks. Some damage patterns can have other explanations, so inspection must consider context.
What protects a VFD-driven motor?
A shaft-grounding ring or brush offers a deliberately engineered low-impedance path that may divert shaft current away from rolling contacts. An insulated bearing interrupts a selected current path; drive-side common-mode filtering, correctly designed shielded cable, and high-frequency bonding can also help. Selection is installation-specific: an insulated bearing alone may redirect current through attached machinery. See Rockwell Automation’s motor-cable guidance and OSEEC.011 on grounding and bonding.
Safe, evidence-based workflow
- Record motor, VFD, cable type and length, bearing history, alarms, vibration trends, and applicable manufacturer instructions.
- Examine approved maintenance reports for bearing pitting, fluting, lubricant condition, and alignment findings.
- Review existing electrical test reports and whether shaft grounding or insulated bearings are specified and installed.
- Have qualified personnel evaluate electrical measurements and protective design under an approved procedure. Do not improvise a live shaft probe or defeat guards and interlocks.
Safety: VFD DC buses may retain hazardous voltage after shutdown. OSEEC.029 explains why Safe Torque Off is not electrical isolation.
Practice and answer key
Question 1: Does a hot bearing prove current damage? Answer: No; temperature alone cannot distinguish electrical erosion from mechanical or lubrication faults.
Question 2: Why might grounding the shaft reduce bearing damage? Answer: A correctly engineered path diverts some high-frequency current away from the lubricated rolling contact.
Question 3: What is fluting? Answer: Repeated, often washboard-like raceway grooves associated with electrical discharge damage, evaluated alongside other evidence.
We volunteer daily to ensure the credibility of the information on this platform is Verifiably True. If you would like to support to help further secure the integrity of our research initiative, please scan the QR code below.


Leave a Reply